The basic grade filter will remove all chlorine, taste, colour and odour but is a basic choice of filter for those mainly concerned with bad tasting or highly chlorinated water. are the most widely used carbon block devices in the world and provide previously unattainable performance at the lowest price point. simultaneously remove chlorine taste and odor and organic chemicals that contribute to taste and odor while providing the particulate filtration and dirt-holding capacity of an efficient 10 μm nominal sediment filter. These filters are optimized for applications where they perform the role of both a sediment and activated carbon filter. The extrusion process allows the production of a carbon block with more carbon, but a lower pressure drop. This enables a filter to deliver extended life while removing sediment, chlorine taste and odor and organic contaminants from water, aqueous solutions or suspensions. The is also widely used in filtering organic solvents. The MATR is ideal for use in residential and commercial water purification systems, food service, pre - and post-RO systems. T is manufactured from high purity acid-washed activated carbon. Its dirt-holding capacity and the absence of carbon fines the filter of choice. A superior carbon block, combines both high performance and integrity with an exceptional cost-to-performance value. As a result, virtually renders GAC filters obsolete by comparison. Extruded Activated Carbon Block Filter The Workhorse 10 μm Nominal Filtration High Adsorptive Capacity and Efficiency Efficient Sediment Filter No Release of Carbon Fines Competitively Priced vs. GAC filters Performance Tested and Verified by Independent Laboratory Testing O.D. x Chlorine Taste & Odor Nominal Initial ΔP Part No. Length Weight Reduction Capacity @ Flow μm Rating @ Flow 32-250-125-975 2.50 x 9.75 0.75 lbs. >6,000 gal. @ 1.0 GPM 5 μm 2.0 psid @ 1.0 GPM 32-250-125-20 2.50 x 20 1.75 lbs. >12,000 gal. @ 2.0 GPM 5 μm 2.0 psid @ 2.0 GPM 32-425-125-975 4.25 x 9.75 2.60 lbs. >12,000 gal. @ 3.0 GPM 5 μm 4.0 psid @ 3.5 GPM 32-425-125-20 4.25 x 20 5.60 lbs. >26,000 gal. @ 7.0 GPM 5 μm 4.5 psid @ 7.0 GPM Technical Specifications and Order Information COMPONENT is Tested and Certified by NSF International under NSF/ANSI Standard 42 for material requirements only. MADE IN USA NSF ORDER INFORMATION Special order filters are available in varying sizes with lengths from 1 to 60. Standard filters are finished with a prefiltration medium. A protective polypropylene netting is applied to the exterior of the cartridge. Polypropylene end caps with compression gaskets fit most standard housings. Inquire concerning alternative filter finishing options, including alternative end cap and housing interface styles, a wide range of non-standard extruded filter sizes, and non-standard prefiltration systems. EXTRUDED CARBON = EXCEPTIONAL VALUE filters consist of activated carbon particles fused into a uniform block with enhanced adsorptive capacity and efficiency. filters flow in a radial (outside-to-inside) direction, providing increased dirt-holding capacity and low pressure drop. Unlike granular activated carbon (GAC) filters, cartridges will not channel or bypass, due to the extreme uniformity of their extruded activated carbon core. Service life of the filter is greatly extended by a prefiltration medium. No channeling No fluidizing No bypassing Eliminates release of carbon fines Lowest extractables, pure materials of construction Maximum service life and resistance to fouling Manufactured using FDA-compliant materials NOTES 1. Performance of a given MATRIKX extruded carbon filter varies in direct proportion to the total weight of carbon in each filter. 2. Projected chlorine taste and odor reduction capacity when tested in accordance with NSF/ANSI Standard 42 protocol. 3. Nominal particulate rating (5 μm) is for >85% of a given size as determined from single-pass particle counting results.* 4. Absolute particulate rating (10 μm) is for >99.9% of particles of a given size as determined from single-pass particle counting results.** 5. Actual results obtained will vary with various combinations of organic contaminants, changes in pH or other conditions encountered in actual use. 6. All information presented here is based on data believed to be reliable. It is offered for evaluation and verification, but is not to be considered a warranty of any kind. 7 filters are designed to fit most standard household and commercial or industrial housings. 8. Contact KX Industries, L.P. to check filter housing compatibility. 9. This cartridge must be placed in an appropriate housing and flushed for a minimum of 5 minutes prior to use. *Nominal Filter Rating: Filter rating indicating the approximate size particle, the majority of which will not pass through the filter. It is generally interpreted as meaning that 85% of the particles of the size equal to the nominal micron rating will be retained by the filter. (WQA Glossary of Terms, Third Edition, 3-97). ** Absolute Filter Rating: Filter rating meaning that 99.9% (or essentially all) of the particles larger than a specific micron rating will be trapped on or within the filter. (WQA Glossary of Terms, Third Edition, 3-97). WARNINGS: Maximum Operating Temperature: 125F Maximum Operating Pressure: 250 psig Maximum Differential Pressure: 100 psid Collapse Pressure: 200 psid filters are not to be autoclaved or steamsterilized.
Write a few sentences to tell people about your store (the kind of products you sell, your mission, etc). You can also add images and videos to help tell your story and generate more interest in your shop.To edit the content on this page, go to the Pages section of your Shopify admin.